Removal of nitrogen and phosphate from wastewater by addition of bittern

Removal of nitrogen and phosphate through crystallization of struvite (MgNH(4)PO(4).6H(2)O) has gained increasing interest. Since wastewaters tend to be low in magnesium relative to ammonia and phosphates, addition of this mineral is usually required to effect the struvite crystallization process. The present study evaluated the feasibility of using bittern, a byproduct of salt manufacture, as a low-cost source of magnesium ions. High reaction rates were observed; the extent of nitrogen and phosphorus removals did not change beyond 10 min. Phosphorus removals from pure solutions with bittern added were equivalent to those obtained with MgCl(2) or seawater. Nitrogen removals with bittern were somewhat lower than with the alternate Mg(2+) sources, however. Application of bittern to biologically treated wastewater from a swine farm achieved high phosphate removal, but ammonia removals were limited by imbalance in the nitrogen:phosphorus ratio.     

Heavy and toxic metals in staple foodstuffs and agriproduct from contaminated soils

This article presents basic data on the content of Cr, Fe, Ni, Cu, Zn, As, Cd, Sb, Hg, and Pb in staple foodstuffs and agriproduct grown in Russia (Astrakhan region and the town of Belovo) and Egypt (Helwan region). The dependence of the concentration of metals in agriproducts on the content and chemical form of existence in irrigation water and soils is indicated.     

Sorption of As(V) ions by akaganéite-type nanocrystals

A priority pollution problem, the removal of arsenate oxyanions from dilute aqueous solutions by sorption onto synthetic akaganéite (beta-FeO(OH)) was the aim of the present study. This is an innovative inorganic adsorbent material prepared in the laboratory, following a new method of preparation. The effect of akaganéite and arsenate concentration, the contact time, temperature, solution pH value, and ionic strength variation on the treatment process was mainly investigated during this study. Typical adsorption isotherms were determined, which were found to fit sufficiently the typical Langmuir equation. The mechanism of sorption was examined by electrokinetic, X-ray diffraction, Fourier transmission infrared and scanning electron microscopy measurements. Promising results were obtained, due to the favourite characteristics of the adsorbent applied.     

Assessment of tin and butyltin species in estuarine superficial sediments from Gipuzkoa,Spain

Ten superficial sediments from river estuaries of Gipuzkoa (North Spain) were collected and analyzed for nine metals (including tin, Sn) and butyltin compounds (monobutyltin, MBT; dibutyltin, DBT; tributyltin, TBT). Total metal concentration in the fine fraction (<63 micrometer) of the sediment was determined in aqua regia--hydrofluoric acid extracts by atomic absorption spectrometry. The butyltin species (BTs) were firstly extracted from the sediments with hydrochloric acid-methanol mixture. After derivatization with sodium tetraethyl borate, the organotin compounds were extracted by solid phase microextraction (SPME) in headspace mode. A fiber coated with 100 micrometer poly(dimethylsiloxane) was used for SPME. The organotin species were analyzed by gas chromatography-flame ionization detection. Analysis of the certified reference sediment (PACS-2) shown the suitability of the procedures for determination of metal contents and DBT-TBT species in contaminated sediments. Factorial analysis was used to examine the main sources of metals. Three factors represented more than 89% of the total variance of the metal system, and the Sn was related with Cu-Zn-Pb suggesting the same pollution source. The BTs concentrations in the area were high (TBT ranged from 0.05 to 5.48 mg Sn kg(-1)). The percentage of total butyltin species ( summation operator BTs) respect to the total Sn amount was higher than 4% in all the sediments, showing in the Bidasoa river estuary a remarkable value higher than 20%. Hence, the studied estuarine sediments reflect a pollution that is related with historical industrial and fishing activities of the area.     

Antimony bioavailability in mine soils

Five British former mining and smelting sites were investigated and found to have levels of total Sb of up to 700 mg kg(-1), indicating high levels of contamination which could be potentially harmful. However, this level of Sb was found to be biologically unavailable over a wide range of pH values, indicating that Sb is relatively unreactive and immobile in the surface layers of the soil, remaining where it is deposited rather than leaching into lower horizons and contaminating ground water. Sb, sparingly soluble in water, was unavailable to the bacterial biosensors tested. The bioluminescence responses were correlated to levels of co-contaminants such as arsenic and copper, rather than to Sb concentrations. This suggests that soil contamination by Sb due to mining and smelting operations is not a severe risk to the environment or human health provided that it is present as immobile species and contaminated sites are not used for purposes which increase the threat of exposure to identified receptors. Co-contaminants such as arsenic and copper are more bioavailable and may therefore be seen as a more significant risk.     

Wet air oxidation of a reactive dye solution using CoAlPO(4)-5 and CeO(2) catalysts

Wet air oxidation of a prepared reactive dye solution was performed to assess the efficacy of CoAlPO(4)-5 and CeO(2) as catalysts in the reaction. Via adsorption and oxidation of dye, CoAlPO(4)-5 effectively decreased American Dye Manufacturers Institute and chemical oxygen demand (COD) values in the dye solution. At a reaction temperature of 135 degrees C and an applied pressure of 1.0 MPa, color and COD removal were as high as 95% and 90%, respectively, after 2 h. Active sites on the outer surface of CoAlPO(4)-5 are responsible for adsorption and decomposition of dye while active sites in the pores dominate further destruction and oxidation of intermediate products. Since the outer surface only represents a minor part of the total surface, the color removal does not increase appreciably with loading of CoAlPO(4)-5. The CeO(2) catalyst, calcined from cerium chloride under high thermal impact (type A CeO(2)) was very effective in removing color and COD from the solution. This catalyst demonstrated near 100% color removal at temperatures above 135 degrees C and the COD removal could be above 95% at 165 degrees C. With both CoAlPO(4)-5 and CeO(2) catalysts, COD rose and then fell back during the reaction, a feature typical of a consecutive reaction. In contrast to prepared CeO(2), a commercial CeO(2) did not exhibit any catalytic ability for the removal of color and COD. The durability of both CoAlPO(4)-5 and prepared CeO(2) is considered to be fair.     

Methods for sampling and analysis of tropospheric ethanol in gaseous and aqueous phases

In this paper, we report on techniques for sampling and measuring ethanol in both the gas and aqueous phases of the lower troposphere. In the gas phase, the best sampling conditions were ensured by adsorption on Hayesep Q with a Chromosorb W AW coated with LiCl dryer (method 1) or by cryogenic trapping (method 2). An intercomparison campaign showed good agreement between both methods under various conditions. Method 1 (adsorption on Hayesep Q with dryer) is easier to set up and to carry away from the laboratory. Method 2 (cryogenic trapping) requires longer sampling time (up to 60 min while method 1 requires only 10-15 min). Method 1 is adapted to high concentrations of ethanol (>20 ppb) and low relative humidity (<30%). Method 2 gives more accurate results than method 1 for low ethanol concentrations (1-20 ppb). Comparing these results to previous studies, it is clear that sampling with appropriate solid adsorbents or with stainless steel canisters (with appropriate humidified air and short storage time) is adapted to urban or industrial environments where ethanol concentrations are high. Cryogenic sampling must be preferred for remote places where ethanol concentrations are low. Three techniques were tested for sampling ethanol in the liquid phase, namely solid phase microextraction, purge and trap injection, and direct injection. Among those, the latter was chosen for field measurements of ethanol in rain samples at an urban location. These first ever results at an urban location show concentrations ranging from <1 to 5 microM in rains, which agree with the expected range of concentrations. However, the purge and trap method showed detection limits that were 50 times lower and should be preferred for liquid phase ethanol measurements in rural and remote locations. Combining cryogenic trapping for the gas phase (method 2) and direct injection for the liquid phase is convenient and well adapted for a multiphase study of ethanol in the atmosphere, where simultaneous measurements in both phases are needed.     

Treatment of chlorinated solvents by TiO2 photocatalysis and photo-Fenton: influence of operating conditions in a solar pilot plant

Titanium dioxide photocatalysis (using 20 0mg l(-1) of TiO2), under aerobic and anaerobic conditions, and photo-Fenton (2 and 56 mg l(-1) iron) were applied to the treatment of different NBCS (non-biodegradable chlorinated solvents), such as dichloroethane, dichloromethane and trichloromethane dissolved in water at 50 mg l(-1). All the tests were performed in a 35-l solar pilot plant with compound parabolic collectors (CPCs) under natural illumination. The two solar treatments were compared with attention to chloride release and TOC mineralisation, as the main parameters. Photo-Fenton was found to be the more appropriate treatment for these compounds, assuming volatilisation as a drawback of photocatalytic degradation of NBCS dissolved in water. In this context, several operating parameters related to NBCS degradation, e.g., treatment time, temperature, hydrogen peroxide consumption and volatility of parent compounds are discussed. The correct choice of operating conditions can very often diminish the problem of volatilisation during treatment.     

Biosorption of water-soluble dyes on magnetically modified Saccharomyces cerevisiae subsp. uvarum cells

Brewer's yeast (bottom yeast, Saccharomyces cerevisiae subsp. uvarum) cells were magnetically modified using water based magnetic fluid stabilized with perchloric acid. Magnetically modified yeast cells efficiently adsorbed various water soluble dyes. The dyes adsorption can be described by the Langmuir adsorption model. The maximum adsorption capacity of the magnetic cells differed substantially for individual dyes; the highest value was found for aniline blue (approx. 220 mg per g of dried magnetic adsorbent).     

Inclusion complexes of alpha- and gamma-cyclodextrins and the herbicide norflurazon: I. Preparation and characterisation. II. Enhanced solubilisation and removal from soils

The interaction of norflurazon with alpha- and gamma-cyclodextrins (CDs) yielded the formation of inclusion complexes at a 1:1 stoichiometric ratio in solution and in the solid state. Apparent stability constants of 50.7+/-1.6 and 37+/-1.7 M(-1) and an increase in herbicide solubility by up to five and fourfold for alpha- and gamma-CD, respectively, were determined from the phase solubility diagrams at 25 degrees C in water. Three processing methods (kneading, spray-drying and vacuum evaporation) were used to prepare norflurazon-CD solid inclusion complexes, which were characterised by infrared spectroscopy, differential scanning calorimetry and scanning electron microscopy. A high increase in the norflurazon dissolution rate was obtained with all the solid complexes with gamma-CD, but when alpha-CD was used, only the solid system obtained after the vacuum evaporation process showed a higher dissolution rate. This finding is a first step in the development of new, environmentally sound formulations of norflurazon (NFL), due to the capacity for increasing its dissolution rate and hydrosolubility, and thus diminishing the use of organic solvents. On the other hand, the effect of alpha- and gamma-cyclodextrin on the solubility of norflurazon in solution was also considered as a way of modifying its behaviour in the soil environment. Desorption studies of NFL from soils in the presence of alpha- and gamma-cyclodextrin were carried out using a batch equilibration method. The results obtained showed that alpha- and gamma-cyclodextrin greatly increased the removal of norflurazon previously adsorbed, proving the potential use of these CDs for in situ remediation of pesticide-contaminated soils.